| 8DF0 ::: IBM Image Adapter/A|
8DF1 ::: IBM Image Adapter/A with Printer/Scanner Option
8DF2 ::: DSS and sub card 2
8DF3 ::: DSS and sub card 3
8DF4 ::: IBM Image Adapter/A
8DF5 ::: IBM Image Adapter/A and Printer/Scanner Option
8DF6 ::: IBM Image-I Adapter
|Image courtesy of EPRM © IBM Corp. 1992-97|
|Part Name||FRU P/N||MKT P/N|
|Image Adapter/A 1MB||06G8224 *||35G4715|
|Image Adapter/A 3MB||66G2279 *||35G4716|
|Image Adapter/A 3MB and 6091-Cable||35G4717|
|6091-019 Video Cable||58F2902|
|Memory Module-DRAM **||07F4407|
|Printer/Scanner Feature Card||07F4403|
|OEM Scanner Cable (25-Pin male-male)||58F4411|
|3812-002 Printer Cable||07F4413|
|4216-020 Printer Cable||07F2474|
* 8550, 8555, 8560, 8570, 8580, 8595 only.
** Not for 8565, 8573, 9047.
Video Cables for Displays
|Display Type||Cable Description||MKT P/N|
|IBM SIMM cable (SIMM connector to 5BNC)||49G2717|
|6091-019||See note below|
|IBM Connector Converter Cable||49G2718|
|1091-051||No special cable needed||--|
|9527||IBM SIMM Cable||95G9906|
|9521||IBM SIMM Cable||95G9907|
6091-019 Display Cable
This cable is required if the Image Adapter/A or the Image-I Adapter/A is supporting an IBM Color Display 6019-019. The cable is supplied with the Image Adapter/A 3MB 6019. The cable (FRU 58F2902) must be ordered separately for all others.
Technical information and illustrations contained in this page are edited excerpts from the EPRM, Copyright © IBM Corp. 1992-97.
The Image Adapter/A is a high-resolution adapter, capable of driving displays up to 128 MHz, with a maximum screen addressability of 1600x1200 pixels. The driver output impedance for video signals is 75 ohms. The sync lines of the adapter are TTL levels driven by 4 ma drivers, therefore the termination should at the very least be at 750 ohms.
The Image Adapter/A is available in three versions:
The three versions of the Image Adapter/A support IBM analog displays equipped with a 15-pin direct-drive analog interface. The adapters can be installed in any IBM PS/2 Micro Channel system unit, except portable models.
Image Adapter/A Options
You can attach optional features only to the Image Adapter/A.
For a single display configuration, you must always attach the display to the display connector on the Image Adapter/A and not to the system-unit display connector.
Image Adapter/A 15-pin Analog Video Connector
The Image-I Adapter/A is a high-resolution adapter, capable of driving displays up to 230 MHz, with a maximum screen addressability of 1600x1280 pixels. It is available in 3MB only. It is ISO (International Organization for Standardization) enabled. The Image-I Adapter/A supports only ISO refresh rates, it does not support non-ISO displays.
The Image-I Adapter/A can be installed in all IBM PS/2 system units except portable models. ISO-enabled IBM display types are 6091-016, 6091-19i, 1091-051, 4517 and the 9504 Monochrome Display. These displays conform with industry and government standards, such as ISO standard 9241/3.
The display attached to the Image Adapter can show VGA graphics only if the adapter is installed in the AVEC slot. Ideally, the Image Adapter should be installed in the AVEC slot unless this slot is already in use (e.g. with an 8514/A Adapter).
Image-I Adapter/A SIM-Video Connector:
ADF Adapter Description File
@8DF0.ADF IBM Image Adapter/A
@8DF1.ADF IBM Image Adapter/A with Printer/Scanner Option
@8DF2.ADF DSS and sub card 2
@8DF3.ADF DSS and sub card 3
@8DF4.ADF IBM Image Adapter/A
@8DF5.ADF IBM Image Adapter/A with Printer/Scanner Option
@8DF6.ADF IBM Image-I Adapter
|Legal | Copyright||top|